I'm going to give it a try. I have a good relationship with my dealer and service department. I'm fairly skilled at things involving electronics. I don't mind giving it a go.

I'll let you know what I find out.

 

While installing a bunch of lights on my 2024 RTL, I found the connector in the attached photos on the left rear brace. It has 3 wires - black for ground, red for power, and orange for what I assume is the video feed from the camera to the instrument panel.

I put a voltage tester across black and red with the ignition on - no power. Then I put the bike in reverse and got +12 volts on red. So this is obviously the connection for the camera.

I'm waiting for someone to get the cameras into stock and will let everyone know how it works once I get my hands on one.

 

Looking forward to the results!

 

I found this diagram here that shows the camera, and the connector looks exactly like the one on my Spyder-

2025 Can-Am Utility Vehicles Parts-Finder Diagrams | McCoy Motorsports Inc., Pikeville KY

 

I'm searching daily for it to come into stock, and also for a picture of a 2025 Sea to Sky that shows a picture of the rear. On the BRP website, it looks like they may have shrunk the size of the reverse light and put the camera next to it. If that is the case, we would also need to replace that panel. Or just mount it under the trunk.

I'll know more once I have the camera in hand.

 

So someone had a dealer mounted the BRP cam to the license plate light housing. That would work but I'd be afraid the screws would vibrate out.

 

I guess that would depends upon what kind of screws they used.

I'd be worried about self-tapping coming out, but a screw with a washer and locknut on the back should be sturdy enough.

 

Exactly what I said in another post. I'm going to check behind the light to see if there is room. I have the cam kit and was poised to return it today until I saw this.

 

Have you hooked up the camera to the connector under the left side rear panel to see if it displays on the screen when the Spyder is put into reverse?

 

No, not yet. I've read it works. I have enabled the cam in the software.

 

Hopefully you will have better luck than I.

 

I can confirm that a backup camera works on a 2024 Spyder RT Limited. I bought a cheap camera on Amazon and was able to get it to work. Give me a few days and I'll post the details.
This was the camera I used

Amazon.com

 

Great! Looking forward to it. Thanks!

 

That is great news Zippy! In addition to the BRP camera, I have a couple of others lying around that I did not use as backup cameras. Guess I could have saved $250.

 

The 3 pin connector that has been discussed previously near the left rear light IS the connector for the camera.

Here are pics of mine.

The male end with end cap plugs is attached to the female end with the wires.

Here is a clip from the maintenance manual of the pinout. I also verified with a voltmeter.

Also, here you can see the Camera (-) eventually goes to ground.

So I connected the cameras - and power - to Camera (-), the cameras power + to Backup Light / 12V Cam , and the cameras signal to Camera (S).

Turned on the Backup Camera in the software and put it in Reverse and the camera image displayed on the screen.

Since this wasn’t the OEM camera, I’m not sure the backup lines mean much.

Also, I’m waiting on some terminal connectors so I can use the existing male end rather than wait 2-4 weeks to get one from Amazon.

Finally, still trying to decide it I will use this camera or buy another one and where to mount it….but at least it works.

Once I get everything finished, I'll post again.

 

Can you simplify the drawing for those of us who are not electrically inclined? I cannot read schematics.

 

Thank you for the detailed explanation and drawings.

As this setup didn't work for me using the BRP camera, I'll have to give it a try with the aftermarket camera I have on the shelf.

 

The 3-pin connector for the camera has-

• a black with yellow stripe - that is the ground for the camera.
• a red that provides power to the camera when the Spyder is put into reverse.
• a tan with black stripe is the feed from the camera to the dash display.

So if you are trying to hook up an aftermarket non-BRP camera, it would be

• black from camera to black/yellow stripe
• red from camera to red
• yellow (most common) from camera to tan/black stripe.

 

Aaahh… Thank You

 

My backup camera project is done!!! And it works great.
My cost for the whole project was $19.99
I already had the tools and a few of the items I used.

5set 1-1703494-1/1488991-5 Car Reversing Radar Eye Plug DJ7032YA-1.2-11/21 Female and Male Waterproof Connector Inserts - $10.00
https://www.amazon.com/dp/B0CL6GSZ78?ref=ppx_yo2ov_dt_b_fed_asin_title

After I bought these, I found they are keyed different, so only the pins work, which is really all you need anyway.

Car Rear View Camera Backup Reverse Camera HD 170° Wide Angle 12 LED Night Vision, for RV Trucks Trailer SUV - $9.99
https://www.amazon.com/dp/B0B95J5JC5?ref=ppx_yo2ov_dt_b_fed_asin_title

I decided to run an extension cable from the original camera connector to under the seat. This way I shouldn't need to disassemble the side of the Spyder if I need to make adjustments. Then another extension with a power and RCA end to under the rear cargo storage.
I then connected those to the camera ends. The camera is attached to under the rear cargo storage with Gorilla tape. I think that will hold it, but will report back if not.
With his setup, I should be able to replace the camera pretty easily if needed.
The downside to this camera is it also has backup lines, but for the cost, I can live with it.
In the picture, the Red Line is 10 inches from the back of the Spyder.

 

My backup camera project is done!!! And it works great.
My cost for the whole project was $19.99
I already had the tools and a few of the items I used.

5set 1-1703494-1/1488991-5 Car Reversing Radar Eye Plug DJ7032YA-1.2-11/21 Female and Male Waterproof Connector Inserts - $10.00
https://www.amazon.com/dp/B0CL6GSZ78?ref=ppx_yo2ov_dt_b_fed_asin_title

Car Rear View Camera Backup Reverse Camera HD 170° Wide Angle 12 LED Night Vision, for RV Trucks Trailer SUV - $9.99
https://www.amazon.com/dp/B0B95J5JC5?ref=ppx_yo2ov_dt_b_fed_asin_title

I decided to run an extension cable from the original camera connector to under the seat. This way I shouldn't need to disassemble the side of the Spyder if I need to make adjustments. Then another extension with a power and RCA end to under the rear cargo storage.
I then connected those to the camera ends. The camera is attached to under the rear cargo storage with Gorilla tape. I think that will hold it, but will report back if not.
With his setup, I should be able to replace the camera pretty easily if needed.
The downside to this camera is it also has backup lines, but for the cost, I can live with it.
In the picture, the Red Line is 10 inches from the back of the Spyder.

View attachment 9005 View attachment 9003
View attachment 9004

Which pins in the connector went to video, power, ground? The RCA barrel plug off the camera contains both the video and the ground correct? So how did you split that to the pin connectors on the spyder and the one you bought off Amazon?

 

Wow, great job! Now I have to tear mine apart and try again to get the factory camera working.

 

What year is your Spider Zippy? Mine is a 2024 Spyder RT Sea to Sky, will this setup work on my Spyder?

 

Mine is a 2024 Spyder RT Limited. The same setup should work on your Spyder as well. I bought a new camera on Amazon ($38) to see if it has a better image. The camera I have now is OK, and works well, but only cost $10. I want to see the difference in the new camera. I'll share results when I try the new camera.

 

Hello, done it myself with amazon backup camera, works and look’s okay, hope.

 

I changed my camera to the following one:

Amazon.com: PixelMan Backup Camera,AHD 1080P Metal 170 Degree Wide Angle Rearview Reversing Camera,PMD2A-S Clear Night Vision IP69 Waterproof Reverse Rear View Camera for Car Vehicle SUV RV : Electronics

Amazon.com: PixelMan Backup Camera,AHD 1080P Metal 170 Degree Wide Angle Rearview Reversing Camera,PMD2A-S Clear Night Vision IP69 Waterproof Reverse Rear View Camera for Car Vehicle SUV RV : Electronics

www.amazon.com

Much better picture than the $10 camera.
It was easy to do with the way I had wired it originally.

 

what connector will work with the three wire BRP backup connection? The one Zippy listed is not available anymore it looks like. Would like to plug directly into the BRP plug. Thanks for the god work in making the camera work.

 

After I ordered the connector, I found the ends are keyed different, but the pins work on the OEM plug, which is all you really need. I would be interested in finding what type of pins they are or as barender has requested,

 

To me it looks like the blank plug that is on the Spyder that holds the supply plug can be pinned and used.

 

As this is my first message, I need to post a second one...

 

Corrected post after actual installation on my 2024 RT LTD:

Male pins

 

HD Backup Camera,Metal Housing 170 Degree Wide View Angle License Plate Rear View Camera for Car,Clear Night Vision IP69 Waterproof Rearview Universal Reverse Cam Kit for Vehicle SUV RV Pickup https://a.co/d/cIaUOWK

Hopefully this link works for the Amazon camera Im installing. I cut green and white and left the orange. (Actually, I had to re connect the orange because I had cut it).

my plan is to install camera underneath the license plate, behind the mudflap. I’ll play around with it tomorrow and see where I end up.

 

Was able to adjust camera a bit for a better view but, still plan on mounting under license plate where it’s horizonta.

 

Here’s my finished camera. I could’ve probably moved it forward all the way to mudflap, but this will work just fine.

One thing for guys without the pins. I cut up a paper clip and soldered it to the wires. Shrink wrapped, taped and split loomed everything up. Worked great so far. 🤞